How long is a mosin nagant m91 30

After antiquated weaponry led to heavy Russian losses during the Russo-Ottoman War, Russian military leadership recognized the urgent need for a more modern infantry rifle. At the time, Russian forces were equipped with single-shot Berdan rifles that were woefully inadequate against newer, magazine-fed rifles. Over the course of the following decade, designers worked to develop a replacement for the Berdan, and in the Russian military accepted trial submissions from Sergei Ivanovich Mosin, Leon Nagant, and a relatively unknown Captain Zinoviev.

Among these are a full upper handguard added before and modified iron sights. This finish is intended to combat some rusting, but bluing, in general, is a poor finish for total rust prevention. Once the rifle is freed from its cosmoline-induced stasis, a thin film of light oil, such as CLP, should be applied to all metal surfaces as a lubricant and preservative. The metal finish, both in terms of machining and bluing, is one facet of the Mosin that suffered most during hasty wartime production.

For the most part, current Mosin imports were refinished at a Soviet military arsenal after World War Two and placed into storage until very recently. It also goes to show just how well cosmoline can preserve a firearm, as many of these imported Mosins are in impeccable condition. Without a surface treatment or finish, the bolt is susceptible to tarnishing or rusting when used with corrosive ammunition or exposed to humid conditions. This is another part that should be well cleaned after each range session and oiled.

Most Mosin-Nagants come with hardwood birch or birch laminate stocks that have been hastily slathered in shellac. Even so, the shellac on common refurbished Mosins was likely restored during the late s and s. In a majority of cases, these rifles were completely re-stocked after the war.

The grain of the birch also ranges from tight and subdued to strong and heavy. Birch is a tough hardwood that works well both as a solid cut or glued as a laminate. Ergonomically, Soviet Mosin-Nagants compare rather poorly to their western counterparts.

Shouldering the rifle is similar to tugging rope due to the very straight profile of the wood stock. Some shooters complain that the Mosin has a short length of pull that is uncomfortable for larger framed people. I have not found this to be an issue at all. The distance from palm to buttplate is very nearly as long as a Mauser Kar. The midsection of the stock features deep finger grooves that are intended to enhance grip comfort. Personally, I find these grooves unnecessary. They are too far rearward to effectively maneuver the muzzle of the It should be noted that Mosin stocks can display significant dimensional variation.

For this reason, some Mosins may feel better than others for some people. Notched tangent rear sights have always been common on continental European firearms, especially Russian arms, and are usually quicker to acquire than the peep style sights that are more often seen on western rifles.

The body of the magazine is wedge-shaped to accommodate the pronounced rim at the base of the 7. This handy little feature facilitates unloading and cleaning the magazine by allowing the entire floorplate to hinge forward.

Like most rifles of its era, the Mosin-Nagant is bolt-action operated. In order to open the bolt for charging and casing extraction, the straight handle must be rotated degrees upward and then briskly pulled rearward until the bolt face bottoms out at the rear of the magazine. Frankly, loading via clip requires more practice than I am currently willing to pursue. Early in a committee consisting of Ye. Kabakov and I. Komaritskii, began work on modernizing the M, using the dragoon model as a basis.

Izhevsk discontinued production in Because supplies of M parts barrels, receivers, stocks, etc. Those produced during the height of the war had at least two distinguishing features: extremely rough milling on the receiver and a high receiver wall on the left side of the receiver.

Both of these measures were intentional to cut down on the milling process and to expedite the guns to the front line soldier. Originally intended for use by Dragoons mounted infantry. Typically, an ex-Dragoon is able to be identified by raising the rear sight and looking where the sight base is located on the dovetail. For more information on the Dragoon rifle, please see: M M Perhaps the most affordable, and common examples of a PU sniper rifle for your collection are the ones that have been arsenal re-finished and re-issued as standard rifles.

In theory, that helped. They realized that the Dragoon no longer had an advantage. From a collectors point of view, they tend to be desirable because its a variation and all good collectors want and need variety. So, how does the home gamer decide if he has a M Ex-Dragoon sitting in a corner gathering dust. There are a couple easy ways to determine this.

Look at the barrel length. Second, Look at the rear sight. The sight base will have gaps in the corners due to the difference between the M91 and M site base. The squared off M sight will leave a void see pics. Third, Look at the markings. A true Ex-Dragoon will have a hex receiver opposed to a round receiver and be pre dated. The example we have in the armory is a Hex receiver with markings for the Izhevsk Ordnance Factory